OFFICE : +971 4546 3606
OFFICE : +971 4546 3606
MS-POE

MS-POE

The MicroScanner Cable Verifier series simplifies the testing of voice, data, and video cable. It starts by taking results from what was four different test modes and displaying them all at once – graphical wiremap, pair lengths, distance to fault, cable ID, and far end device. What’s more, it supports virtually any type of low-voltage cable testing with no need for awkward adapters. The end result is reduced test time and technician error. That makes high-quality installations more efficient than ever.

Next-generation MicroScanner verifies voice/data/video cable and services with a revolutionary user interface.

Datasheet - MS-POE

Datasheet - MS-POE

Fluke Networks Products Catalog

Fluke Networks Products Catalog

Documents:

Datasheet - MS-POE

Datasheet - MS-POE

Fluke Networks Products Catalog

Fluke Networks Products Catalog

Key Features

• Quickly determine if a problem is caused by a bad or unconnected cable, insufficient power, or a Powered Device (PD).
• Information for the Network Engineer to investigate potential switch configuration or malfunctions.
• PoE Switch Verification – Determine if a switch port can provide enough power by reporting PoE class (0-8).
• Powered Pairs – Graphically identifies powered pairs. Including Dual Signature where the switch port delivers power on 2 or 4 pairs (802.3bt or PoE ++)
• Active Switch Detection - Determine if a cable is connected to a switch port and port speed up to 10G
• Cable Testing – Identify any shorted, open or crossed wires at both ends, length of each pair, and send tones to find cables.
• Validate and troubleshoot your Industrial Ethernet copper cabling
• PoE Injector verification - Display injector voltage level

Comparison Chart
MicroScanner2 MicroScanner PoE
Twisted Pair (RJ-11, RJ-45)
Wiremap ✓✓
Length / Distance to Fault ✓✓
Coaxial
Length / Distance to Fault ✓
Service Identification
Reports Maximum Power Class ✓
10/100/1000BASE-T ✓✓
2.5GBASE-T, 5GBASE-T, 10GBASE-T ✓
Power Over Ethernet 802.3af802.3af, 802.3at, 802.3bt
Analog and Digital Toning ✓✓
Optional Remote Identifiers ✓✓

Yesterday’s cable verification testers force users to toggle between up to four different modes of operation to view all test results. This not only slows the test process, but also causes frustration and leads to high user error rates. MicroScanner2 has defeated this convention by displaying key test results – wiremap, pair lengths, distance to fault, cable ID, and far end device – all on one screen. Plus it features an oversized, backlit LCD screen with the power to display wiremap results graphically, which brings unprecedented comfort and clarity to the user experience.

Tired of losing or breaking all the adapters needed for testing the various voice, data, and video media types? MicroScanner2 makes these awkward adapters things of the past with built-in RJ11, RJ45, and coax support. Both the main unit and the far-end identifiers can be used to test telephone jacks, Ethernet jacks, and CATV outlets right out of the box. Just one more way MicroScanner2 streamlines cable verification.

MicroScanner2 features built-in IntelliTone digital and analog toning to precisely locate virtually any cable or wire pair, regardless of work environment. Use digital mode to locate high-grade data cabling (Cat 5e/6/6a) in bundles, or at switches, patch panels, or wall outlets. Digital mode especially performs in environments with high data, RF, or electromagnetic interference. When coupled with the IntelliTone 200 Pro Probe, it can also be used to verify cable wiremap from either the tester end or the probe end.
Use analog mode on voice-grade cabling (Cat 3 and below), as well as coax, security/alarm, and speaker wiring. These cables are optimized for lower frequency transmissions, and therefore are more easily isolated with a low-frequency tone. MicroScanner2’s smart analog tone eliminates frustrating guesswork locating individual wire pairs during installations by changing songs each time the pair under test is shorted together. This provides technicians a decisive way to identify individual wire pairs before punching them down or when diagnosing voice transmission problems.

Voice, data, video technicians have a lot more problems to deal with than just the cabling. They have to rule out a whole host of potential cable and service issues before determining the cause of a connection problem. MicroScanner2 acknowledges this, giving technicians high power vision to detect today’s most common service problems. Detect the presence of POTS voltage and verify polarity. Verify powered 10/100/1000 Ethernet switches at the far end. Or, confirm proper PoE voltage and pairs.

MicroScanner PoE cuts through the confusion of your PoE installation by providing swift and simple PoE verification. The tester detects the available PoE class (0-8) provided by the connected switch in accordance to the latest PoE standards and displays the voltage from passive PoE sources. This information keeps the technician informed on the installations capabilities and improves their work flow and reduces the time spent waiting for information about the connected switch.

Industrial environments are much harsher and more time sensitive than traditional IT environments. Connectivity failures can be caused by cabling faults can disrupt communications, resulting in production delays. Technicians need to rule out a whole host of cable and service issues before determining the cause of a connectivity problem. Where is the cable broken? Are all the wires properly terminated? Is there a switch at the far end? Is PoE available? The MicroScanner Series provides technicians the vision to troubleshoot these issues and get production back up and running.
The MicroScanner™ Series Industrial Ethernet kits allow technicians to perform continuity tests on RJ45, M12X, M12D, and M8D terminated cables in seconds and displays results graphically so you can see wiremap, pair lengths, distance to fault, cable ID, and if the cable is connected to a far-end device. Cable failures result in costly production downtime so it’s important to quickly identify where the cable is broken so it can be replaced or repaired. 

Get a Quote

This field is for validation purposes and should be left unchanged.