+971 4 320-6053

Welcome to Synergix International!

Gallery loading...
Mouseover Zoom loading...


FI-7000 FiberInspector™ Pro

This product, you earn 120 loyalty point(s).

Regular Price: AED 15,480.00

Special Price AED 12,900.00

Availability: In stock



Fiber optic connector end-face contamination is a leading cause of fiber failures. Dirt and contaminant cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fiber loss and OTDR testing can expose this problem, but in many cases, dirty connections make fiber testing time consuming and inaccurate.

Since dirt can be an issue before, during, or after fiber optic certification testing, and migrate from one fiber optic connector end-face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated fiber optic connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected as protective caps do not keep fiber optic connector end-faces clean. Avoiding this common cause of failure, starts with inspecting the fiber optic connector end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.

The FI-7000 FiberInspector Pro is a fiber optic inspection scope that allows you to inspect and certify fiber optic connector end-faces in 1 seconds so you can get the job done the first time. This fiber optic inspection scope provides automated PASS/FAIL certification take the guess work out of fiber inspection so anyone can be a fiber expert.

1-second automated PASS/FAIL certification of fiber optic connector end-faces
  1. Automated Pass/Fail certification of fiber optic connector end-faces
  2. Graphical indication of problem areas due to contamination, pits, chips, and scratches
  3. Certify to industry standards - IEC 61300-3-35
  4. Eliminate human subjectivity from fiber optic connector end-face measurements
  5. Save fiber optic connector end-face views during certification process
  6. Versiv™ modular design supports copper certification, fiber optic loss, OTDR testing and fiber end-face inspection


  • Fiber Inspection Certification
    • Certify your fiber end-faces to industry standards - IEC 61300-3-35. Or if you prefer, you can manually grade your end-faces.
  • Graphical indication of Problem Areas
    • FiberInspector Pro highlights defects found on fiber end-faces. Instead of just coloring the defect area, the FI-7000 colors the defect and highlights the defect’s background so that the defect is clearly visible. Defects that fail the standard’s requirements are colored Red, while defects that pass are colored Green.
  • Store End-face Images
    • Store both end-face images of a fiber directly in your Versiv test results. Combine end-face images with CertiFiber Pro OLTS and/or OptiFiber Pro OTDR test results for the complete history of your fiber cabling health.
  • Built on the Versiv Platform
    • The FI-7000 is built on the Versiv Cable Certification Platform which enables you to easily add optical loss (OLTS) and Optical Time Domain Reflectometry (OTDR) or even twisted pair copper or network analysis functionality to FI-7000. Product add-on kits are available for the DTX CableAnalyzer, CertiFiber Pro OLTS, and OptiFiber Pro OTDR.
  • Versiv’s ProjX™ System
    • Versiv’s ProjX™ System manages jobs from setup to systems acceptance, ensuring that all tests are completed correctly. Enter the testing details for a job once, and ProjX stores them in a project file with a name the whole team can understand. Change modules or jobs without having to re-enter details. Support multiple testers on the same job by sharing project files via USB sticks or email. Easy just met efficient.

      Set-up or view test limits, and testing attributes.   Project menu screen shows percent complete per job.   Project Specific screen shows up to the minute project details.
  • Taptive™ User Interface
    • Now you can test across multiple media types and requirements as easy as using a smartphone. Simply, select the job you’re working on, and the large display confirms the test that needs to be performed. Taptive helps you tap into the overall cabling infrastructure faster and more easily.

      User Interface for Speeds Troubleshooting
    • Taptive user interface simplifies set-up,eliminates errors and speeds troubleshooting
  • LinkWare™ Live Test Results Management Service
    1. LinkWare Live is a cloud-based service that lets you manage certification jobs anytime, anywhere, with anyone on any device.  With LinkWare Live, you can
    2. Keep track of every test on every job.  Get an overview of every project from any smart device. Drill down to each individual test. Instantly receive notification of incorrect test setting or cable IDs.
    3. Get it right the first time. Define cable IDs and test settings from your PC or tablet. Then send them to the testers or Brother printers at the jobsite for mistake-free testing and labeling.
    4. Keep your testers up to date. Standards can change without notice, and an out-of-date test report can mean hours of re-testing. LinkWare Live automatically ensures your testers are running the latest.
    5. Stop wasting time and gas driving testers back to the office. Upload your test results straight from the job site to LinkWare Live over Wi-Fi. Then download them automatically to the right job for fast report generation with LinkWare PC.
    6. Avoid Project Delays. Track the last used location and monitor the status of all testers to ensure they are always calibrated and running the latest firmware*
    7. Supports all Versiv models: DSX CableAnalyzer Series, CertiFiber Pro, OptiFiber Pro, and the FI-7000.
  • LinkWare™ Management Software
    1. Project managers have full capabilities to monitor workflow and consolidate test results.
    2. LinkWare pulls data togther into a single report that is easy for customers to understand, showcasing quality and workmanship. LinkWare stats, provides automated statistical reports that turns test results into charts to reveal performance. The report even summarizes your entire cabling and fiber infrastructure in one compact, graphical format, so it is easy to verify margins and anomalies.
  • PASS/FAIL Fiber End-face Grading
    • The FI-7000’s PASS/FAIL fiber end-face grading is available to all Versiv owners. It is included in Versiv firmware v3.0 and higher. To enjoy this free fiber end-face grading, just download the latest Versiv firmware and create a new Project using FiberInspector as the test.


Technical Specifications

Inspection Probe specifications


2M pixels

Blue LED

Light source

Blue LED

Power source

Versiv mainframe

Field of View (FOV)

Horizontal: 425 µm

Vertical: 320 µm

Minimum detectable particle size

0.5 µm


Approximately 6.75 in x 1.5 in (1175 mm x 35 mm) without adapter tip


200 g

Temperature range

Operating: 32°F to 122°F (0 °C to +50 °C)

Storage: -4°F to +158°F (-20°C to +70°C)





General specifications



Mainframe with module and battery: 3 lbs, 5 oz (1.28 kg)


Mainframe with module and battery: 2.625 in x 5.25 in x 11.0 in ( 6.67 cm x 13.33 cm x 27.94 cm)


Lithium ion battery pack, 7.2 volts

Battery life

Eleven hour with Inspection probe attached



Charge Time


Tester Off

Four hours to charge from 10% to 90% capacity

Tester On

Six hours to charge from 10% to 90% capacity with the tester on



Environmental specifications


Operating temperature*

-18ºC to 45ºC

Non-operating temperature

-30ºC to 60ºC

Operating altitude

4,000 m (13123 ft)

3200 m (10,500 ft) with ac adapter

Storage altitude

12,000 m


EN 61326-1



* Do not keep battery at temperatures below -20°C (-4°F) or above 50°C (122°F) for periods longer than one week to maintain battery capacity.


The FI-7000 FiberInspector Pro contains:

Versiv Mainframe, USB Fiber Inspection Video Probe with 4 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal), Blank Module to protect the mainframe’s rear connector, AC Charger, Shoulder Strap, USB Interface Cable, Versiv Open Source Software CD, Getting Started Guide, Soft Carrying Case.

Why shop with Synergix International, UAE’s leading online seller of Fluke Networks testers?

Synergix International is proud to supply a huge range of cable testers, fiber testers, phone testers, hand tools, certification testers, cable fault diagnostics equipment, fiber cleaning tools, termination tools and more from Fluke Networks. You can buy Fluke Networks online through our website 24/7 for fast and reliable delivery.

Synergix International is one of UAE's leading online sellers of data products & accessories. Backed by the Synergix Group, we have access to the biggest brands such as Fluke Networks, Fluke Industrial, NetScout, Viavi Solutions, Infilink technologies, INNO Instruments, Ekahau, Altai Technologies, Kyoritsu, AiRISTA, Amprobe , Motwane and more - as well as the very best pricing & quick delivery.

Here are just a few reasons our customers keep coming back:

  1. Free shipping on orders over 3000 AED
  2. Secure payment methods (VISA, Mastercard & PayPal)
  3. Stock fulfilment from free zone and locally
  4. Helpful support base located in Dubai, UAE (call +971 4 320 6053 to speak with us)
  5. 24/7 Online chat support

If you are looking for Fluke Networks testing equipment that is not currently listed on our website, please get in contact with us for pricing and lead-times. We have direct partnerships with all suppliers and can source just about anything quickly and at a great price.

Get in touch with us today +971 4 320 6053!

Product Video
  1. Ease of Use Review by Govind

    Good option to certify Fiber End-face for someone who already own DSX unit. Easy to use with same Versiv setup (Posted on 8/19/2018)

Write Your Own Review

You're reviewing: FI-7000

How do you rate this product? *
1 1 star
2 2 star
3 3 star
4 4 star
5 5 star
Make an Enquiry

* Required Fields

Essential Extras